Plumbing 101: A Necessity for Installing a Bathtub
Plumbing 101: A Necessity for Installing a Bathtub
Blog Article
Listed here below you'll find additional sound help and advice regarding Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately challenging task. If the old tub is easily obtainable, the project can relocate immediately; if you have to open up a wall to remove the old bathtub and also place the new bath tub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will require a helper to vacate the old tub and set in the brand-new one. See to it you have actually qualified on your own for the task and also are comfortable trying it. As opposed to working with a professional to take over a halfway-completed project, it is much better to think about utilizing one prior to you begin. Chances are you may need a specialist plumber to make tube links.
This post will aid you set up a brand-new tub in your washroom if you have actually currently acquired a new bathtub as well as do not need to change the plan of your previous water system pipes.
Your devices and material checklist should make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be fairly problematic due to the restricted access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in location in between the tap and the sink. Safeguard the faucet in place with the producer supplied backnut. When the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wooden boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the bath tub up until the level checks out level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the water supply and inspect all joints and brand-new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise check the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, fix the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the tub ought to wait up until the bath tub has actually been utilized a minimum of once as this will settle it right into its final setting.
Getting ready for the Installation
To start with, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and also the tiling, resulting in complications with dampness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also installations. They are marketed in tubes and cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can fracture rather very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily readily available on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on Tools You Need to Install a New Bathtub , I figured sharing that post was a good idea. Feel free to take the opportunity to distribute this post if you enjoyed it. We appreciate reading our article about How to Install a Bathtub Yourself.
Efficient, reliable plumbing services here. Report this page